Advanced-protection HPS Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour les appareils électriques Advanced-protection HPS. Advanced Protection HPS User Manual Manuel d'utilisatio
- Page / 24
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
V
Installation, Operation
& Maintenance Manual
(800) 237-4567
·
(727) 535-6339
·
Fax (727) 539-8955
Advanced Protection Technologies
www.aptsurge.com
·
14550 58th Street North
·
Clearwater, Florida 33760
UL is a registered trademark of Underwriters Laboratories, NEC
®
and National Electrical Code are
registered trademarks of National Fire Protection Association, C62.41.1-2002, C62.41.2-2002,
C62.45-2002, C62.72-2007 are registered trademarks of IEEE.
01.14.13.lh #8380
European Authorized Representative
Obelis s.a.
Boulevard Général Wahis 53
1030 Brussels, BELGIUM
Tel: +(32) 2. 732.59.54
Fax: +(32) 2. 732.60.03
E-Mail: [email protected]
ENGLISH
Surge Protective Device (SPD)
Bonding and Grounding Hazard
Verify that the neutral conductor in the service entrance
equipment is bonded to ground in accordance with the
National Electric Code (NEC
®
) and all applicable codes.
Verify that the neutral terminal (XO) on the secondary side of
distribution transformers are grounded to the system ground in
accordance with the NEC
®
and all applicable codes.
During installation into an electrical system the SPD must
not be energized until the electrical system is completely
installed, inspected and tested. All conductors must be
connected and functional including the neutral (if required).
The voltage rating of the SPD and system must be veried
before energizing the SPD.
Failure to follow these guidelines can lead to abnormally high
voltages at the SPD. This may cause the SPD to fail. The
warranty is voided if the SPD is incorrectly installed and/or if
Safety First – Hazardous Voltage & Shock Hazard
WARNING – IMPORTANT – PLEASE READ – WARNING
• Only qualied licensed electricians should install or service SPDs
• Hazardous voltages exist within SPDs
• SPDs should never be installed or serviced when energized
• Use appropriate safety precautions including Personal Protection Equipment
• Failure to follow these instructions can result in death, serious injury, and/or equipment damage
• This manual shall be read in its entirety prior to installing
the neutral conductor in the service entrance equipment or
downstream of separately derived systems is not bonded to
ground in accordance with the NEC
®
.
Do Not Hi-Pot Test SPDs
Any factory or on-site testing of power distribution
equipment that exceeds normal operating voltage such as
high-potential insulation testing, or any other tests where the
suppression components will be subjected to higher voltage
than their rated Maximum Continuous Operating Voltage
(MCOV) must be conducted with the SPD disconnected
from the power source. For 4-wire systems, the neutral
connection at the SPD must also be disconnected prior to
performing high-potential testing and then reconnected after
test completion.
Failure to disconnect SPD and associated components
during elevated voltage testing will damage the SPD and
will void the warranty.
TE
HP &
TE
HPS,
Series
TE/HP
TE/HPS
XTE/HP &
XTE/HPS
- HP & 1
- Figure 1 2
- TABLE 1: MODEL NUMBER DECODER 3
- Table 2: 4
- DIMENSIONS & WEIGHTS 4
- INSTALLATION 6
- Figure 8 7
- ELECTRICAL DRAWINGS 7
- Flush Mount front view 8
- Figure 6 9
- Figure 5 9
- Table 3: 10
- Order # Part Description 10
- Table 4: FUSE-ALL SERIES 10
- Figure 9 11
- Figure 10 12
- TROUBLESHOOTING FLOWCHART 12
- Figura 1 14
- Article 285 & UL 1449-3 14
- Figura 2 15
- Tabla 2: 16
- DIMENSIONES Y PESOS 16
- INSTALACIÓN 18
- Figura 8 19
- Figura 4 20
- Figura 3 20
- Flush Mount Side View 21
- Tabla 4: 22
- REEMPLAZO DEL MÓDULO 22
- Order # Descripción 22
- Tabla 3: FUSIBLES 22
- Figura 9 23
- REEMPLAZO DEL MODULO 23
- Figura 10 24
Résumé du contenu
Page 1 - HP &
VInstallation, Operation & Maintenance Manual(800) 237-4567·(727) 535-6339 · Fax (727) 539-8955 Advanced Protection Technologieswww.aptsurge.com ·
Page 2 - Figure 1
10MAINTENANCESPDs require minimal maintenance. We recommend periodic inspection of diagnostic indicators to ensure proper operation. We also recommend
Page 3 - TABLE 1: MODEL NUMBER DECODER
11Figure 9MODULE REMOVAL & REPLACEMENT
Page 4 - DIMENSIONS & WEIGHTS
12Figure 10TROUBLESHOOTING FLOWCHART
Page 5
(800) 237-4567·(727) 535-6339 · Fax (727) 539-8955 Advanced Protection Technologieswww.aptsurge.com · [email protected] 58th Street North · Clearw
Page 6 - INSTALLATION
INTRODUCCIÓNGracias por seleccionar un Dispositivo Protector contra Sobretensiones Transitorias (DPS) marca APT. Este es un equipo de alta calidad, su
Page 7 - ELECTRICAL DRAWINGS
3Desembalaje e Inspección PreliminarInspeccione completamente el empaque en cuanto a daño o señales de mal manejo. Quite los materiales de empaque y a
Page 8 - Flush Mount front view
PLANIFICACIÓN & PRE-INSTALACIÓNAmbiente de OperaciónLa unidad estándar está en un gabinete tipo1/12/3R/4. Antes de la instalación, asegure que su
Page 9 - Figure 5
5no tiene ninguna referencia a tierra y sabemos que van a causar inestabilidad en ciertas situaciones. Tal inestabilidad puede causar uctuaciones en
Page 10 - Table 4: FUSE-ALL SERIES
6INSTALACIÓNPlanee con anticipación su instalación. Usted tendrá que cumplir con lo siguiente: ▪ Cumplir con todos los códigos nacionales y locales (N
Page 11 - Figure 9
7Figura 8PLANOS ELÉCTRICOS PARA CONEXIONES TÍPICASTE/1HPSPLIT2 Hots, 1 Neu, 1 GrndHot (BLK)Hot (BLK)Neutral (WHT)VV}}Ground (GRN)TE/3HPHI-LEG DELTA (B
Page 12 - TROUBLESHOOTING FLOWCHART
2INTRODUCTIONThank you for choosing an APT Surge Protective Device (SPD). This is a high quality, high energy surge suppressor designed to protect sen
Page 13
NEMA 3R oricios de perforación para el chasis de acero estándarA n de mantener una calicación UL 3R, dos 0,25” (6mm) agujeros deb
Page 14 - Article 285 & UL 1449-3
Flush Mount Side ViewOpción de contactos secosUn juego de contactos secos de Forma C está incluido con la opción de Contacto Secos. Los Contactos Seco
Page 15 - Figura 2
MANTENIMIENTOLos DPSs requieren mínimo mantenimiento. Recomendamos inspección periódica de los indicadores de diagnóstico para asegurar la operación a
Page 16 - DIMENSIONES Y PESOS
Figura 9REEMPLAZO DEL MODULO11
Page 17
12Figura 10DIAGRAMA PARA LA SOUCIÓN DE PROBLEMASCOMIENZOAlarma audible/Visual LED rojo de servicio onPosibles fallas tarjeta de diagnóstico llamar APT
Page 18 - INSTALACIÓN
3Storage EnvironmentThis SPD should be stored in a clean, dry environment. Storage temperature range is -40°C (-40°F) to +60°C (+140°F). Avoid exposur
Page 19 - Figura 8
4PRE-INSTALLATION & INSTALLATION PLANNINGOperating EnvironmentThe standard unit uses a Type 1/12/3R/4 enclosure. Non-metallic polycarbonate 4X, st
Page 20 - Figura 3
5SPDs for ungrounded systems can be installed on grounded systems with a clamping performance penalty. However, SPDs for grounded systems installed on
Page 21 - Flush Mount Side View
6INSTALLATIONPre-Plan your installation. You will need to accomplish the following: ▪ Meet all National and Local codes. (NEC® Article 285 addresses S
Page 22 - Tabla 3: FUSIBLES
7Figure 8ELECTRICAL DRAWINGSTE/1HPSPLIT2 Hots, 1 Neu, 1 GrndHot (BLK)Hot (BLK)Neutral (WHT)VV}}Ground (GRN)TE/3HPHI-LEG DELTA (B High)3 Hots, (B HIGH)
Page 23 - REEMPLAZO DEL MODULO
NEMA 3R Drain Holes for Standard Steel EnclosureIn order to maintain a UL 3R rating, two 0.25” (6mm) holes must be drilled in opposite corners of the
Page 24 - Figura 10
The surge counter includes Test and Reset buttons on the touchpad display. Pressing Test adds one count. Pressing Reset clears the counter’s memory an
Produits connexes et manuels pour Accessoires pour les appareils électriques Advanced-protection HPS
(12 pages)
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.934 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels